OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt3050.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "edimax,3g-6200nl", "ralink,rt3050-soc"; |
||
10 | model = "Edimax 3g-6200nl"; |
||
11 | |||
12 | cfi@1f000000 { |
||
13 | compatible = "cfi-flash"; |
||
14 | reg = <0x1f000000 0x800000>; |
||
15 | bank-width = <2>; |
||
16 | device-width = <2>; |
||
3 | office | 17 | #address-cells = <1>; |
18 | #size-cells = <1>; |
||
1 | office | 19 | |
3 | office | 20 | partition@0 { |
21 | label = "u-boot"; |
||
22 | reg = <0x0 0x30000>; |
||
23 | read-only; |
||
24 | }; |
||
1 | office | 25 | |
3 | office | 26 | partition@30000 { |
27 | label = "u-boot-env"; |
||
28 | reg = <0x30000 0x10000>; |
||
29 | read-only; |
||
30 | }; |
||
1 | office | 31 | |
3 | office | 32 | factory: partition@40000 { |
33 | label = "factory"; |
||
34 | reg = <0x40000 0x10000>; |
||
35 | read-only; |
||
36 | }; |
||
1 | office | 37 | |
3 | office | 38 | partition@3e0000 { |
39 | label = "cimage"; |
||
40 | reg = <0x3e0000 0x20000>; |
||
41 | read-only; |
||
42 | }; |
||
1 | office | 43 | |
3 | office | 44 | partition@50000 { |
45 | label = "firmware"; |
||
46 | reg = <0x50000 0x390000>; |
||
1 | office | 47 | }; |
48 | }; |
||
49 | |||
3 | office | 50 | gpio-leds { |
1 | office | 51 | compatible = "gpio-leds"; |
52 | |||
3 | office | 53 | internet { |
1 | office | 54 | label = "3g-6200nl:green:internet"; |
55 | gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
||
56 | }; |
||
57 | |||
58 | wlan { |
||
59 | label = "3g-6200nl:green:wlan"; |
||
60 | gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; |
||
61 | }; |
||
62 | }; |
||
63 | |||
3 | office | 64 | gpio-keys-polled { |
1 | office | 65 | compatible = "gpio-keys-polled"; |
3 | office | 66 | #address-cells = <1>; |
67 | #size-cells = <0>; |
||
1 | office | 68 | poll-interval = <20>; |
69 | |||
70 | reset { |
||
71 | label = "reset"; |
||
72 | gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; |
||
73 | linux,code = <KEY_RESTART>; |
||
74 | }; |
||
75 | }; |
||
76 | }; |
||
77 | |||
78 | &pinctrl { |
||
79 | state_default: pinctrl0 { |
||
80 | gpio { |
||
81 | ralink,group = "spi", "i2c", "jtag", "rgmii", "mdio", "uartf"; |
||
82 | ralink,function = "gpio"; |
||
83 | }; |
||
84 | }; |
||
85 | }; |
||
86 | |||
87 | ðernet { |
||
88 | mtd-mac-address = <&factory 0x4>; |
||
89 | }; |
||
90 | |||
91 | &esw { |
||
92 | mediatek,portdisable = <0x37>; |
||
93 | }; |
||
94 | |||
95 | &wmac { |
||
96 | ralink,mtd-eeprom = <&factory 0>; |
||
97 | }; |
||
98 | |||
99 | &otg { |
||
100 | status = "okay"; |
||
101 | }; |