OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | #include "qcom-ipq8064-v2.0.dtsi" |
2 | |||
3 | #include <dt-bindings/input/input.h> |
||
4 | |||
5 | / { |
||
6 | model = "TP-Link Archer VR2600v"; |
||
7 | compatible = "tplink,vr2600v", "qcom,ipq8064"; |
||
8 | |||
9 | memory@0 { |
||
10 | reg = <0x42000000 0x1e000000>; |
||
11 | device_type = "memory"; |
||
12 | }; |
||
13 | |||
14 | reserved-memory { |
||
15 | #address-cells = <1>; |
||
16 | #size-cells = <1>; |
||
17 | ranges; |
||
18 | rsvd@41200000 { |
||
19 | reg = <0x41200000 0x300000>; |
||
20 | no-map; |
||
21 | }; |
||
22 | }; |
||
23 | |||
24 | aliases { |
||
25 | serial0 = &gsbi4_serial; |
||
26 | mdio-gpio0 = &mdio0; |
||
27 | |||
28 | led-boot = &power; |
||
29 | led-failsafe = &general; |
||
30 | led-running = &power; |
||
31 | led-upgrade = &general; |
||
32 | }; |
||
33 | |||
34 | chosen { |
||
3 | office | 35 | linux,stdout-path = "serial0:115200n8"; |
1 | office | 36 | }; |
37 | |||
38 | soc { |
||
39 | pinmux@800000 { |
||
40 | led_pins: led_pins { |
||
41 | mux { |
||
42 | pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17", |
||
43 | "gpio26", "gpio53", "gpio56", "gpio66"; |
||
44 | function = "gpio"; |
||
45 | drive-strength = <2>; |
||
46 | bias-pull-up; |
||
47 | }; |
||
48 | }; |
||
49 | |||
50 | i2c4_pins: i2c4_pinmux { |
||
51 | mux { |
||
52 | pins = "gpio12", "gpio13"; |
||
53 | function = "gsbi4"; |
||
54 | drive-strength = <12>; |
||
55 | bias-disable; |
||
56 | }; |
||
57 | }; |
||
58 | |||
59 | button_pins: button_pins { |
||
60 | mux { |
||
61 | pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68"; |
||
62 | function = "gpio"; |
||
63 | drive-strength = <2>; |
||
64 | bias-pull-up; |
||
65 | }; |
||
66 | }; |
||
67 | |||
68 | spi_pins: spi_pins { |
||
69 | mux { |
||
70 | pins = "gpio18", "gpio19", "gpio21"; |
||
71 | function = "gsbi5"; |
||
72 | bias-pull-down; |
||
73 | }; |
||
74 | |||
75 | data { |
||
76 | pins = "gpio18", "gpio19"; |
||
77 | drive-strength = <10>; |
||
78 | }; |
||
79 | |||
80 | cs { |
||
81 | pins = "gpio20"; |
||
82 | drive-strength = <10>; |
||
83 | bias-pull-up; |
||
84 | }; |
||
85 | |||
86 | clk { |
||
87 | pins = "gpio21"; |
||
88 | drive-strength = <12>; |
||
89 | }; |
||
90 | }; |
||
91 | |||
92 | mdio0_pins: mdio0_pins { |
||
93 | mux { |
||
94 | pins = "gpio0", "gpio1"; |
||
95 | function = "gpio"; |
||
96 | drive-strength = <8>; |
||
97 | bias-disable; |
||
98 | }; |
||
99 | }; |
||
100 | |||
101 | rgmii2_pins: rgmii2_pins { |
||
102 | mux { |
||
103 | pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", |
||
104 | "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; |
||
105 | function = "rgmii2"; |
||
106 | drive-strength = <8>; |
||
107 | bias-disable; |
||
108 | }; |
||
109 | }; |
||
110 | }; |
||
111 | |||
112 | gsbi@16300000 { |
||
113 | qcom,mode = <GSBI_PROT_I2C_UART>; |
||
114 | status = "ok"; |
||
115 | serial@16340000 { |
||
116 | status = "ok"; |
||
117 | }; |
||
118 | /* |
||
119 | * The i2c device on gsbi4 should not be enabled. |
||
120 | * On ipq806x designs gsbi4 i2c is meant for exclusive |
||
121 | * RPM usage. Turning this on in kernel manifests as |
||
122 | * i2c failure for the RPM. |
||
123 | */ |
||
124 | }; |
||
125 | |||
126 | gsbi5: gsbi@1a200000 { |
||
127 | qcom,mode = <GSBI_PROT_SPI>; |
||
128 | status = "ok"; |
||
129 | |||
130 | spi4: spi@1a280000 { |
||
131 | status = "ok"; |
||
132 | |||
133 | pinctrl-0 = <&spi_pins>; |
||
134 | pinctrl-names = "default"; |
||
135 | |||
136 | cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; |
||
137 | |||
138 | flash: W25Q128@0 { |
||
139 | compatible = "jedec,spi-nor"; |
||
140 | #address-cells = <1>; |
||
141 | #size-cells = <1>; |
||
142 | spi-max-frequency = <50000000>; |
||
143 | reg = <0>; |
||
144 | |||
145 | SBL1@0 { |
||
146 | label = "SBL1"; |
||
147 | reg = <0x0 0x20000>; |
||
148 | read-only; |
||
149 | }; |
||
150 | |||
151 | MIBIB@20000 { |
||
152 | label = "MIBIB"; |
||
153 | reg = <0x20000 0x20000>; |
||
154 | read-only; |
||
155 | }; |
||
156 | |||
157 | SBL2@40000 { |
||
158 | label = "SBL2"; |
||
159 | reg = <0x40000 0x40000>; |
||
160 | read-only; |
||
161 | }; |
||
162 | |||
163 | SBL3@80000 { |
||
164 | label = "SBL3"; |
||
165 | reg = <0x80000 0x80000>; |
||
166 | read-only; |
||
167 | }; |
||
168 | |||
169 | DDRCONFIG@100000 { |
||
170 | label = "DDRCONFIG"; |
||
171 | reg = <0x100000 0x10000>; |
||
172 | read-only; |
||
173 | }; |
||
174 | |||
175 | SSD@110000 { |
||
176 | label = "SSD"; |
||
177 | reg = <0x110000 0x10000>; |
||
178 | read-only; |
||
179 | }; |
||
180 | |||
181 | TZ@120000 { |
||
182 | label = "TZ"; |
||
183 | reg = <0x120000 0x80000>; |
||
184 | read-only; |
||
185 | }; |
||
186 | |||
187 | RPM@1a0000 { |
||
188 | label = "RPM"; |
||
189 | reg = <0x1a0000 0x80000>; |
||
190 | read-only; |
||
191 | }; |
||
192 | |||
193 | APPSBL@220000 { |
||
194 | label = "APPSBL"; |
||
195 | reg = <0x220000 0x80000>; |
||
196 | read-only; |
||
197 | }; |
||
198 | |||
199 | APPSBLENV@2a0000 { |
||
200 | label = "APPSBLENV"; |
||
201 | reg = <0x2a0000 0x40000>; |
||
202 | read-only; |
||
203 | }; |
||
204 | |||
205 | OLDART@2e0000 { |
||
206 | label = "OLDART"; |
||
207 | reg = <0x2e0000 0x40000>; |
||
208 | read-only; |
||
209 | }; |
||
210 | |||
211 | kernel@320000 { |
||
212 | label = "kernel"; |
||
213 | reg = <0x320000 0x300000>; |
||
214 | }; |
||
215 | |||
216 | rootfs@620000 { |
||
217 | label = "rootfs"; |
||
218 | reg = <0x620000 0x960000>; |
||
219 | }; |
||
220 | |||
221 | defaultmac: default-mac@0xfaf100 { |
||
222 | label = "default-mac"; |
||
223 | reg = <0xfaf100 0x00200>; |
||
224 | read-only; |
||
225 | }; |
||
226 | |||
227 | ART@fc0000 { |
||
228 | label = "ART"; |
||
229 | reg = <0xfc0000 0x40000>; |
||
230 | read-only; |
||
231 | }; |
||
232 | }; |
||
233 | }; |
||
234 | }; |
||
235 | |||
236 | phy@100f8800 { /* USB3 port 1 HS phy */ |
||
237 | status = "ok"; |
||
238 | }; |
||
239 | |||
240 | phy@100f8830 { /* USB3 port 1 SS phy */ |
||
241 | status = "ok"; |
||
242 | }; |
||
243 | |||
244 | phy@110f8800 { /* USB3 port 0 HS phy */ |
||
245 | status = "ok"; |
||
246 | }; |
||
247 | |||
248 | phy@110f8830 { /* USB3 port 0 SS phy */ |
||
249 | status = "ok"; |
||
250 | }; |
||
251 | |||
252 | usb30@0 { |
||
253 | status = "ok"; |
||
254 | }; |
||
255 | |||
256 | usb30@1 { |
||
257 | status = "ok"; |
||
258 | }; |
||
259 | |||
260 | pcie0: pci@1b500000 { |
||
261 | status = "ok"; |
||
262 | }; |
||
263 | |||
264 | pcie1: pci@1b700000 { |
||
265 | status = "ok"; |
||
266 | force_gen1 = <1>; |
||
267 | }; |
||
268 | |||
269 | mdio0: mdio { |
||
270 | compatible = "virtual,mdio-gpio"; |
||
271 | #address-cells = <1>; |
||
272 | #size-cells = <0>; |
||
273 | gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; |
||
274 | pinctrl-0 = <&mdio0_pins>; |
||
275 | pinctrl-names = "default"; |
||
276 | |||
277 | phy0: ethernet-phy@0 { |
||
3 | office | 278 | device_type = "ethernet-phy"; |
1 | office | 279 | reg = <0>; |
280 | qca,ar8327-initvals = < |
||
281 | 0x00004 0x7600000 /* PAD0_MODE */ |
||
282 | 0x00008 0x1000000 /* PAD5_MODE */ |
||
283 | 0x0000c 0x80 /* PAD6_MODE */ |
||
284 | 0x000e4 0x6a545 /* MAC_POWER_SEL */ |
||
285 | 0x000e0 0xc74164de /* SGMII_CTRL */ |
||
286 | 0x0007c 0x4e /* PORT0_STATUS */ |
||
287 | 0x00094 0x4e /* PORT6_STATUS */ |
||
288 | >; |
||
289 | }; |
||
290 | |||
291 | phy4: ethernet-phy@4 { |
||
3 | office | 292 | device_type = "ethernet-phy"; |
1 | office | 293 | reg = <4>; |
294 | }; |
||
295 | }; |
||
296 | |||
297 | gmac1: ethernet@37200000 { |
||
298 | status = "ok"; |
||
299 | phy-mode = "rgmii"; |
||
300 | qcom,id = <1>; |
||
301 | |||
302 | pinctrl-0 = <&rgmii2_pins>; |
||
303 | pinctrl-names = "default"; |
||
304 | |||
305 | mtd-mac-address = <&defaultmac 0>; |
||
306 | mtd-mac-address-increment = <1>; |
||
307 | |||
308 | fixed-link { |
||
309 | speed = <1000>; |
||
310 | full-duplex; |
||
311 | }; |
||
312 | }; |
||
313 | |||
314 | gmac2: ethernet@37400000 { |
||
315 | status = "ok"; |
||
316 | phy-mode = "sgmii"; |
||
317 | qcom,id = <2>; |
||
318 | |||
319 | mtd-mac-address = <&defaultmac 0>; |
||
320 | |||
321 | fixed-link { |
||
322 | speed = <1000>; |
||
323 | full-duplex; |
||
324 | }; |
||
325 | }; |
||
326 | }; |
||
327 | |||
3 | office | 328 | gpio-keys { |
1 | office | 329 | compatible = "gpio-keys"; |
330 | pinctrl-0 = <&button_pins>; |
||
331 | pinctrl-names = "default"; |
||
332 | |||
333 | wifi { |
||
334 | label = "wifi"; |
||
335 | gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; |
||
336 | linux,code = <KEY_RFKILL>; |
||
337 | }; |
||
338 | |||
339 | reset { |
||
340 | label = "reset"; |
||
341 | gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>; |
||
342 | linux,code = <KEY_RESTART>; |
||
343 | }; |
||
344 | |||
345 | wps { |
||
346 | label = "wps"; |
||
347 | gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; |
||
348 | linux,code = <KEY_WPS_BUTTON>; |
||
349 | }; |
||
350 | |||
351 | dect { |
||
352 | label = "dect"; |
||
353 | gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>; |
||
354 | linux,code = <KEY_PHONE>; |
||
355 | }; |
||
356 | |||
357 | ledswitch { |
||
358 | label = "ledswitch"; |
||
359 | gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; |
||
360 | linux,code = <KEY_LIGHTS_TOGGLE>; |
||
361 | }; |
||
362 | }; |
||
363 | |||
3 | office | 364 | gpio-leds { |
1 | office | 365 | compatible = "gpio-leds"; |
366 | pinctrl-0 = <&led_pins>; |
||
367 | pinctrl-names = "default"; |
||
368 | |||
369 | dsl { |
||
370 | label = "vr2600v:white:dsl"; |
||
371 | gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; |
||
372 | }; |
||
373 | |||
374 | usb { |
||
375 | label = "vr2600v:white:usb"; |
||
376 | gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; |
||
377 | }; |
||
378 | |||
379 | lan { |
||
380 | label = "vr2600v:white:lan"; |
||
381 | gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; |
||
382 | }; |
||
383 | |||
384 | wlan2g { |
||
385 | label = "vr2600v:white:wlan2g"; |
||
386 | gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>; |
||
387 | }; |
||
388 | |||
389 | wlan5g { |
||
390 | label = "vr2600v:white:wlan5g"; |
||
391 | gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>; |
||
392 | }; |
||
393 | |||
394 | power: power { |
||
395 | label = "vr2600v:white:power"; |
||
396 | gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; |
||
397 | default-state = "keep"; |
||
398 | }; |
||
399 | |||
400 | phone { |
||
401 | label = "vr2600v:white:phone"; |
||
402 | gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; |
||
403 | }; |
||
404 | |||
405 | wan { |
||
406 | label = "vr2600v:white:wan"; |
||
407 | gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>; |
||
408 | }; |
||
409 | |||
410 | general: general { |
||
411 | label = "vr2600v:white:general"; |
||
412 | gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>; |
||
413 | }; |
||
414 | }; |
||
415 | }; |
||
416 | |||
417 | &adm_dma { |
||
418 | status = "ok"; |
||
419 | }; |