OpenWrt – Blame information for rev 2

Subversion Repositories:
Rev:
Rev Author Line No. Line
1 office 1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2 /dts-v1/;
3  
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6  
7 #include "qca956x.dtsi"
8  
9 / {
10 model = "Phicomm K2T";
11 compatible = "phicomm,k2t", "qca,qca9563";
12  
13 aliases {
14 led-boot = &status_red;
15 led-failsafe = &status_red;
16 led-running = &status_red;
17 led-upgrade = &status_red;
18 };
19  
20 chosen {
21 bootargs = "console=ttyS0,115200n8";
22 };
23  
24 leds {
25 compatible = "gpio-leds";
26  
27 status_blue {
28 label = "phicomm:blue:status";
29 gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
30 };
31  
32 status_red: status_red {
33 label = "phicomm:red:status";
34 gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
35 };
36  
37 status_yellow {
38 label = "phicomm:yellow:status";
39 gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
40 };
41 };
42  
43 keys {
44 compatible = "gpio-keys-polled";
45 poll-interval = <20>;
46  
47 reset {
48 linux,code = <KEY_RESTART>;
49 gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
50 debounce-interval = <60>;
51 };
52 };
53 };
54  
55 &uart {
56 status = "okay";
57 };
58  
59 &gpio {
60 status = "okay";
61 };
62  
63 &pcie {
64 status = "okay";
65 };
66  
67 &spi {
68 num-cs = <1>;
69  
70 status = "okay";
71  
72 flash@0 {
73 compatible = "jedec,spi-nor";
74 reg = <0>;
75 spi-max-frequency = <25000000>;
76  
77 partitions {
78 compatible = "fixed-partitions";
79 #address-cells = <1>;
80 #size-cells = <1>;
81  
82 partition@0 {
83 label = "u-boot";
84 reg = <0x000000 0x30000>;
85 read-only;
86 };
87  
88 partition@30000 {
89 label = "config";
90 reg = <0x030000 0x10000>;
91 read-only;
92 };
93  
94 partition@40000 {
95 label = "permanent";
96 reg = <0x040000 0x50000>;
97 read-only;
98 };
99  
100 partition@90000 {
101 compatible = "denx,uimage";
102 label = "firmware";
103 reg = <0x090000 0xf60000>;
104 };
105  
106 art: partition@ff0000 {
107 label = "art";
108 reg = <0xff0000 0x010000>;
109 read-only;
110 };
111 };
112 };
113 };
114  
115 &mdio0 {
116 status = "okay";
117  
118 phy-mask = <0>;
119  
120 phy0: ethernet-phy@0 {
121 reg = <0>;
122 phy-mode = "sgmii";
123  
124 qca,ar8327-initvals = <
125 0x04 0x00080080 /* PORT0 PAD MODE CTRL */
126 0x10 0x81000080 /* POWER_ON_STRIP */
127 0x50 0xcc35cc35 /* LED_CTRL0 */
128 0x54 0xcb37cb37 /* LED_CTRL1 */
129 0x58 0x00000000 /* LED_CTRL2 */
130 0x5c 0x00f3cf00 /* LED_CTRL3 */
131 0x7c 0x0000007e /* PORT0_STATUS */
132 >;
133 };
134 };
135  
136 &eth0 {
137 status = "okay";
138  
139 pll-data = <0x03000101 0x00000101 0x00001919>;
140  
141 phy-mode = "sgmii";
142 phy-handle = <&phy0>;
143 };
144  
145 &wmac {
146 status = "okay";
147 mtd-cal-data = <&art 0x1000>;
148 };