OpenWrt – Blame information for rev 2

Subversion Repositories:
Rev:
Rev Author Line No. Line
1 office 1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2 /dts-v1/;
3  
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6  
7 #include "qca956x.dtsi"
8  
9 / {
10 model = "D-Link DIR-859 A1";
11 compatible = "dlink,dir-859-a1", "qca,qca9563";
12  
13 aliases {
14 led-boot = &power;
15 led-failsafe = &power;
16 led-running = &power;
17 led-upgrade = &power;
18 };
19  
20 chosen {
21 bootargs = "console=ttyS0,115200n8";
22 };
23  
24 leds {
25 compatible = "gpio-leds";
26  
27 wps {
28 label = "dir-859-a1:green:wps";
29 gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
30 };
31  
32 power: power {
33 label = "dir-859-a1:green:power";
34 gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
35 };
36  
37 internet {
38 label = "dir-859-a1:green:internet";
39 gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
40 };
41  
42 wlan {
43 label = "dir-859-a1:green:wlan";
44 gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
45 linux,default-trigger = "phy0tpt";
46 };
47 };
48  
49 keys {
50 compatible = "gpio-keys-polled";
51 poll-interval = <20>;
52  
53 wps {
54 linux,code = <KEY_RESTART>;
55 gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
56 debounce-interval = <60>;
57 };
58  
59 reset {
60 linux,code = <KEY_RESTART>;
61 gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
62 debounce-interval = <60>;
63 };
64 };
65  
66 gpio-export {
67 compatible = "gpio-export";
68 #size-cells = <0>;
69  
70 gpio_switch_reset {
71 gpio-export,name = "dir-859-a1:reset:switch";
72 gpio-export,output = <1>;
73 gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
74 };
75 };
76 };
77  
78 &uart {
79 status = "okay";
80 };
81  
82 &gpio {
83 status = "okay";
84 };
85  
86 &pcie {
87 status = "okay";
88 };
89  
90 &spi {
91 num-cs = <1>;
92  
93 status = "okay";
94  
95 flash@0 {
96 compatible = "jedec,spi-nor";
97 reg = <0>;
98 spi-max-frequency = <30000000>;
99  
100 partitions {
101 compatible = "fixed-partitions";
102 #address-cells = <1>;
103 #size-cells = <1>;
104  
105 partition@0 {
106 label = "bootloader";
107 reg = <0x000000 0x40000>;
108 read-only;
109 };
110  
111 partition@40000 {
112 label = "bdcfg";
113 reg = <0x040000 0x10000>;
114 read-only;
115 };
116  
117 partition@50000 {
118 label = "devdata";
119 reg = <0x050000 0x10000>;
120 read-only;
121 };
122  
123 partition@60000 {
124 label = "devconf";
125 reg = <0x060000 0x10000>;
126 read-only;
127 };
128  
129 partition@70000 {
130 compatible = "seama";
131 label = "firmware";
132 reg = <0x070000 0xf80000>;
133 };
134  
135 art: partition@ff0000 {
136 label = "art";
137 reg = <0xff0000 0x010000>;
138 read-only;
139 };
140 };
141 };
142 };
143  
144 &mdio0 {
145 status = "okay";
146  
147 phy-mask = <0>;
148  
149 phy0: ethernet-phy@0 {
150 reg = <0>;
151 phy-mode = "sgmii";
152  
153 qca,ar8327-initvals = <
154 0x04 0x00080080 /* PORT0 PAD MODE CTRL */
155 0x10 0x81000080 /* POWER_ON_STRIP */
156 0x50 0xcc35cc35 /* LED_CTRL0 */
157 0x54 0xcb37cb37 /* LED_CTRL1 */
158 0x58 0x00000000 /* LED_CTRL2 */
159 0x5c 0x00f3cf00 /* LED_CTRL3 */
160 0x7c 0x0000007e /* PORT0_STATUS */
161 >;
162 };
163 };
164  
165 &eth0 {
166 status = "okay";
167  
168 pll-data = <0x03000101 0x00000101 0x00001919>;
169  
170 phy-mode = "sgmii";
171 phy-handle = <&phy0>;
172 };
173  
174 &wmac {
175 status = "okay";
176 qca,no-eeprom;
177 };