OpenWrt – Blame information for rev 2

Subversion Repositories:
Rev:
Rev Author Line No. Line
1 office 1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2 /dts-v1/;
3  
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6  
7 #include "ar9344.dtsi"
8  
9 / {
10 model = "Winchannel WB2000";
11 compatible = "winchannel,wb2000", "qca,ar9344";
12  
13 chosen {
14 bootargs = "console=ttyS0,115200n8";
15 };
16  
17 aliases {
18 led-boot = &led_system;
19 led-failsafe = &led_system;
20 led-running = &led_system;
21 led-upgrade = &led_system;
22 };
23  
24 i2c {
25 compatible = "i2c-gpio";
26 gpios = <&gpio 17 GPIO_ACTIVE_HIGH
27 &gpio 16 GPIO_ACTIVE_HIGH
28 >;
29 #address-cells = <1>;
30 #size-cells = <0>;
31  
32 rtc@68 {
33 compatible = "dallas,ds1339";
34 reg = <0x68>;
35 };
36 };
37  
38 leds {
39 compatible = "gpio-leds";
40  
41 wlan2g {
42 label = "wb2000:green:2g";
43 gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
44 linux,default-trigger = "phy0tpt";
45 };
46  
47 usb {
48 label = "wb2000:green:usb";
49 gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
50 trigger-sources = <&hub_port1>, <&hub_port2>;
51 linux,default-trigger = "usbport";
52 };
53  
54 led_system: system {
55 label = "wb2000:green:system";
56 gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
57 default-state = "on";
58 };
59 };
60  
61 keys {
62 compatible = "gpio-keys-polled";
63 poll-interval = <50>;
64  
65 reset {
66 linux,code = <KEY_RESTART>;
67 gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
68 debounce-interval = <60>;
69 };
70 };
71  
72 ath9k-leds {
73 compatible = "gpio-leds";
74  
75 wlan {
76 label = "wb2000:green:5g";
77 gpios = <&ath9k 6 GPIO_ACTIVE_LOW>;
78 linux,default-trigger = "phy1tpt";
79 };
80 };
81 };
82  
83 &ref {
84 clock-frequency = <40000000>;
85 };
86  
87 &uart {
88 status = "okay";
89 };
90  
91 &spi {
92 num-cs = <1>;
93  
94 status = "okay";
95  
96 flash@0 {
97 compatible = "jedec,spi-nor";
98 reg = <0>;
99 spi-max-frequency = <25000000>;
100  
101 partitions {
102 compatible = "fixed-partitions";
103 #address-cells = <1>;
104 #size-cells = <1>;
105  
106 partition@0 {
107 label = "u-boot";
108 reg = <0x0 0x40000>;
109 read-only;
110 };
111  
112 partition@40000 {
113 label = "u-boot-env";
114 reg = <0x40000 0x10000>;
115 read-only;
116 };
117  
118 partition@50000 {
119 label = "firmware";
120 reg = <0x50000 0xf80000>;
121 compatible = "denx,uimage";
122 };
123  
124 partition@fd0000 {
125 label = "nvram";
126 reg = <0xfd0000 0x10000>;
127 read-only;
128 };
129  
130 art: partition@fe0000 {
131 label = "art";
132 reg = <0xfe0000 0x10000>;
133 read-only;
134 };
135  
136 addr: partition@ff0000 {
137 label = "addr";
138 reg = <0xff0000 0x10000>;
139 read-only;
140 };
141 };
142 };
143 };
144  
145 &pcie {
146 status = "okay";
147  
148 ath9k: wifi@0,0 {
149 compatible = "pci168c,0030";
150 reg = <0x0000 0 0 0 0>;
151 qca,no-eeprom;
152 mtd-mac-address = <&addr 0x0>;
153 mtd-mac-address-increment = <0x10>;
154 #gpio-cells = <2>;
155 gpio-controller;
156 };
157 };
158  
159 &usb {
160 #address-cells = <1>;
161 #size-cells = <0>;
162 status = "okay";
163  
164 port@1 {
165 #address-cells = <1>;
166 #size-cells = <0>;
167 reg = <1>;
168 #trigger-source-cells = <0>;
169  
170 hub_port1: port@1 {
171 reg = <1>;
172 #trigger-source-cells = <0>;
173 };
174  
175 hub_port2: port@2 {
176 reg = <2>;
177 #trigger-source-cells = <0>;
178 };
179 };
180 };
181  
182 &usb_phy {
183 status = "okay";
184 };
185  
186 &wmac {
187 status = "okay";
188  
189 mtd-cal-data = <&art 0x1000>;
190 mtd-mac-address = <&addr 0x0>;
191 };
192  
193 &mdio0 {
194 status = "okay";
195  
196 phy-mask = <0x10>;
197  
198 phy4: ethernet-phy@4 {
199 reg = <4>;
200 };
201 };
202  
203 &eth0 {
204 status = "okay";
205  
206 pll-data = <0xe000000 0x04000101 0x04001313>;
207  
208 mtd-mac-address = <&addr 0x0>;
209 mtd-mac-address-increment = <0x21>;
210  
211 phy-mode = "rgmii-rxid";
212 phy-handle = <&phy4>;
213  
214 gmac-config {
215 device = <&gmac>;
216 rgmii-gmac0 = <1>;
217 rxd-delay = <1>;
218 rxdv-delay = <1>;
219 };
220 };