OpenWrt – Blame information for rev 2

Subversion Repositories:
Rev:
Rev Author Line No. Line
1 office 1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2 /dts-v1/;
3  
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6  
7 #include "ar9344.dtsi"
8  
9 / {
10 model = "PowerCloud Systems CR5000";
11 compatible = "pcs,cr5000", "qca,ar9344";
12  
13 aliases {
14 serial0 = &uart;
15 led-boot = &status;
16 led-failsafe = &status;
17 led-running = &status;
18 led-upgrade = &status;
19 };
20  
21 keys {
22 compatible = "gpio-keys-polled";
23 poll-interval = <20>;
24  
25 pinctrl-names = "default";
26 pinctrl-0 = <&jtag_disable_pins>;
27  
28 reset {
29 label = "Reset button";
30 linux,code = <KEY_RESTART>;
31 gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
32 debounce-interval = <60>;
33 };
34  
35 wps {
36 label = "WPS button";
37 linux,code = <KEY_WPS_BUTTON>;
38 gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
39 debounce-interval = <60>;
40 };
41 };
42  
43 leds {
44 compatible = "gpio-leds";
45  
46 status: power {
47 label = "pcs:amber:power";
48 gpios = <&gpio 2 GPIO_ACTIVE_LOW>,
49 <&gpio 4 GPIO_ACTIVE_LOW>;
50 default-state = "on";
51 };
52  
53 wlan2g {
54 label = "pcs:blue:wlan";
55 gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
56 linux,default-trigger = "phy0tpt";
57 };
58  
59 wps_white {
60 label = "pcs:white:wps";
61 gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
62 };
63 };
64 };
65  
66 &ref {
67 clock-frequency = <25000000>;
68 };
69  
70 &uart {
71 status = "okay";
72 };
73  
74 &gpio {
75 status = "okay";
76 };
77  
78 &spi {
79 num-cs = <1>;
80  
81 status = "okay";
82  
83 flash@0 {
84 compatible = "jedec,spi-nor";
85 reg = <0>;
86 spi-max-frequency = <25000000>;
87  
88 partitions {
89 compatible = "fixed-partitions";
90 #address-cells = <1>;
91 #size-cells = <1>;
92  
93 uboot: partition@0 {
94 label = "u-boot";
95 reg = <0x000000 0x040000>;
96 read-only;
97 };
98  
99 partition@40000 {
100 label = "u-boot-env";
101 reg = <0x040000 0x010000>;
102 read-only;
103 };
104  
105 partition@50000 {
106 compatible = "denx,uimage";
107 label = "firmware";
108 reg = <0x050000 0x07a0000>;
109 };
110  
111 art: partition@7f0000 {
112 label = "art";
113 reg = <0x7f0000 0x010000>;
114 read-only;
115 };
116 };
117 };
118 };
119  
120 &usb {
121 status = "okay";
122 #address-cells = <1>;
123 #size-cells = <0>;
124  
125 hub_port1: port@1 {
126 reg = <1>;
127 #trigger-source-cells = <0>;
128 };
129 };
130  
131 &usb_phy {
132 status = "okay";
133 };
134  
135 &pcie {
136 status = "okay";
137  
138 ath9k: wifi@0,0 {
139 compatible = "pci168c,0030";
140 reg = <0x0000 0 0 0 0>;
141 mtd-mac-address = <&art 0x5002>;
142 #gpio-cells = <2>;
143 gpio-controller;
144 };
145 };
146  
147 &mdio0 {
148 status = "okay";
149  
150 phy-mask = <0>;
151  
152 phy0: ethernet-phy@0 {
153 reg = <0>;
154 phy-mode = "rgmii";
155 qca,ar8327-initvals = <
156 0x04 0x07600000 /* PORT0 PAD MODE CTRL */
157 0x10 0x81000080 /* POWER_ON_STRAP */
158 0x50 0xcc35cc35 /* LED_CTRL0 */
159 0x54 0xca35ca35 /* LED_CTRL1 */
160 0x58 0xc935c935 /* LED_CTRL2 */
161 0x5c 0x03ffff00 /* LED_CTRL3 */
162 0x7c 0x0000007e /* PORT0_STATUS */
163 >;
164 };
165 };
166  
167 &eth0 {
168 #address-cells = <1>;
169 #size-cells = <0>;
170 status = "okay";
171  
172 /* default for ar934x, except for 1000M */
173 pll-data = <0x06000000 0x00000101 0x00001616>;
174  
175 mtd-mac-address = <&art 0x0>;
176  
177 phy-mode = "rgmii";
178 phy-handle = <&phy0>;
179  
180  
181 aliases {
182 ag0 = &eth1;
183 };
184  
185 port@0 {
186 compatible = "swconfig,port";
187 reg = <0>;
188 swconfig,segment = "lan";
189 swconfig,portmap = <1 1>;
190 };
191  
192 port@1 {
193 compatible = "swconfig,port";
194 reg = <1>;
195 swconfig,segment = "lan";
196 swconfig,portmap = <2 2>;
197 };
198  
199 port@2 {
200 compatible = "swconfig,port";
201 reg = <2>;
202 swconfig,segment = "lan";
203 swconfig,portmap = <3 3>;
204 };
205  
206 port@3 {
207 compatible = "swconfig,port";
208 reg = <3>;
209 swconfig,segment = "lan";
210 swconfig,portmap = <4 4>;
211 };
212  
213 port@4 {
214 compatible = "swconfig,port";
215 reg = <4>;
216 swconfig,segment = "wan";
217 swconfig,portmap = <5 5>;
218 };
219 };
220  
221 &wmac {
222 status = "okay";
223  
224 mtd-cal-data = <&art 0x1000>;
225 mtd-mac-address = <&art 0x1002>;
226 };