OpenWrt – Blame information for rev 2

Subversion Repositories:
Rev:
Rev Author Line No. Line
1 office 1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2 /dts-v1/;
3  
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6  
7 #include "ar9344.dtsi"
8  
9 / {
10 compatible = "iodata,etg3-r", "qca,ar9344";
11 model = "I-O DATA ETG3-R";
12  
13 aliases {
14 led-boot = &power;
15 led-failsafe = &power;
16 led-running = &power;
17 led-upgrade = &power;
18 };
19  
20 leds {
21 compatible = "gpio-leds";
22  
23 power: power {
24 label = "etg3-r:green:power";
25 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
26 default-state = "on";
27 };
28  
29 notification {
30 label = "etg3-r:green:notification";
31 gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
32 };
33 };
34  
35 keys {
36 compatible = "gpio-keys-polled";
37 poll-interval = <20>;
38  
39 reset {
40 label = "reset";
41 linux,code = <KEY_RESTART>;
42 gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
43 debounce-interval = <60>;
44 };
45 };
46 };
47  
48 &ref {
49 clock-frequency = <40000000>;
50 };
51  
52 &spi {
53 num-cs = <1>;
54 status = "okay";
55  
56 flash@0 {
57 compatible = "jedec,spi-nor";
58 reg = <0>;
59 spi-max-frequency = <25000000>;
60  
61 partitions {
62 compatible = "fixed-partitions";
63 #address-cells = <1>;
64 #size-cells = <1>;
65  
66 partition@0 {
67 label = "u-boot";
68 reg = <0x000000 0x040000>;
69 read-only;
70 };
71  
72 partition@40000 {
73 label = "u-boot-env";
74 reg = <0x040000 0x010000>;
75 };
76  
77 partition@50000 {
78 compatible = "denx,uimage";
79 label = "firmware";
80 reg = <0x050000 0x780000>;
81 };
82  
83 partition@7d0000 {
84 label = "Config";
85 reg = <0x07d0000 0x10000>;
86 read-only;
87 };
88  
89 partition@7e0000 {
90 label = "Rsv";
91 reg = <0x07e0000 0x10000>;
92 read-only;
93 };
94  
95 partition@7f0000 {
96 label = "ART";
97 reg = <0x7f0000 0x010000>;
98 read-only;
99 };
100 };
101 };
102 };
103  
104 &mdio0 {
105 status = "okay";
106  
107 phy0: ethernet-phy@0 {
108 reg = <0>;
109 phy-mode = "rgmii";
110  
111 qca,ar8327-initvals = <
112 0x04 0x07600000 /* PORT0 PAD MODE CTRL */
113 0x50 0xffb7ffb7 /* LED_CTRL0 */
114 0x54 0xffb7ffb7 /* LED_CTRL1 */
115 0x58 0xffb7ffb7 /* LED_CTRL2 */
116 0x5c 0x03ffff00 /* LED_CTRL3 */
117 0x7c 0x0000007e /* PORT0_STATUS */
118 >;
119 };
120 };
121  
122 &eth0 {
123 status = "okay";
124  
125 pll-data = <0x0e000000 0x00000101 0x00001616>;
126  
127 phy-mode = "rgmii";
128 phy-handle = <&phy0>;
129  
130 gmac-config {
131 device = <&gmac>;
132  
133 rgmii-gmac0 = <1>;
134 rxd-delay = <3>;
135 rxdv-delay = <3>;
136 };
137 };
138  
139 &uart {
140 status = "okay";
141 };