OpenWrt – Blame information for rev 2

Subversion Repositories:
Rev:
Rev Author Line No. Line
1 office 1 // SPDX-License-Identifier: GPL-2.0
2 /dts-v1/;
3  
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6  
7 #include "ar9132.dtsi"
8  
9 / {
10 compatible = "tplink,tl-wa901nd-v2", "qca,ar9132";
11 model = "TP-Link TL-WA901ND v2";
12  
13 aliases {
14 led-boot = &system;
15 led-failsafe = &system;
16 led-running = &system;
17 led-upgrade = &system;
18 };
19  
20 extosc: ref {
21 compatible = "fixed-clock";
22 #clock-cells = <0>;
23 clock-frequency = <40000000>;
24 };
25  
26 keys {
27 compatible = "gpio-keys";
28  
29 reset {
30 label = "reset";
31 linux,code = <KEY_RESTART>;
32 gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
33 debounce-interval = <60>;
34 };
35  
36 qss {
37 label = "qss";
38 linux,code = <KEY_WPS_BUTTON>;
39 gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
40 debounce-interval = <60>;
41 };
42 };
43  
44 leds {
45 compatible = "gpio-leds";
46  
47 system: system {
48 label = "tp-link:green:system";
49 gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
50 };
51  
52 qss {
53 label = "tp-link:green:qss";
54 gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
55 };
56  
57 wlan {
58 label = "tp-link:green:wlan";
59 gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
60 linux,default-trigger = "phy0tpt";
61 };
62 };
63 };
64  
65 &uart {
66 status = "okay";
67 };
68  
69 &pll {
70 clocks = <&extosc>;
71 };
72  
73 &spi {
74 status = "okay";
75 num-cs = <1>;
76  
77 flash@0 {
78 compatible = "jedec,spi-nor";
79 reg = <0>;
80 spi-max-frequency = <25000000>;
81  
82 partitions {
83 compatible = "fixed-partitions";
84 #address-cells = <1>;
85 #size-cells = <1>;
86  
87 uboot: partition@0 {
88 label = "u-boot";
89 reg = <0x000000 0x020000>;
90 read-only;
91 };
92  
93 partition@1 {
94 compatible = "tplink,firmware";
95 label = "firmware";
96 reg = <0x020000 0x3D0000>;
97 };
98  
99 art: partition@2 {
100 label = "art";
101 reg = <0x3F0000 0x010000>;
102 read-only;
103 };
104 };
105 };
106 };
107  
108 &mdio0 {
109 status = "okay";
110  
111 phy0: ethernet-phy@c {
112 reg = <0xc>;
113 phy-mode = "mii";
114 };
115 };
116  
117 &eth0 {
118 status = "okay";
119  
120 phy-mode = "mii";
121 mtd-mac-address = <&uboot 0x1fc00>;
122  
123 phy-handle = <&phy0>;
124 };
125  
126 &wmac {
127 status = "okay";
128 mtd-cal-data = <&art 0x1000>;
129 mtd-mac-address = <&uboot 0x1fc00>;
130 };