OpenWrt – Blame information for rev 2
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | #!/bin/bash |
2 | # |
||
3 | # tftp flash script for wireless routers |
||
4 | # |
||
5 | # Copyright (C) 2004 by Oleg I. Vdovikin <oleg@cs.msu.su> |
||
6 | # Copyright (C) 2005 by Waldemar Brodkorb <wbx@openwrt.org> |
||
7 | # |
||
8 | # This program is free software; you can redistribute it and/or modify |
||
9 | # it under the terms of the GNU General Public License as published by |
||
10 | # the Free Software Foundation; either version 2 of the License, or |
||
11 | # (at your option) any later version. |
||
12 | # |
||
13 | # This program is distributed in the hope that it will be useful, |
||
14 | # but WITHOUT ANY WARRANTY; without even the implied warranty of |
||
15 | # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU |
||
16 | # General Public License for more details. |
||
17 | # |
||
18 | # You should have received a copy of the GNU General Public License |
||
19 | # along with this program; if not, write to the Free Software |
||
20 | # Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA |
||
21 | # |
||
22 | |||
23 | if [ -z "$1" ] || [ ! -f $1 ] || [ -z $2 ]; then |
||
24 | echo Usage: $0 firmware vendor |
||
25 | cat << EOF |
||
26 | IMPORTANT: |
||
27 | Notes for Linksys / Asus WL500gx router: |
||
28 | be sure you have set boot_wait to yes. Power on your router |
||
29 | after executing this script. |
||
30 | |||
31 | Notes for Asus WL500g router: |
||
32 | be sure POWER led is flashing (If this is not the case |
||
33 | poweroff the device, push the reset button & power on |
||
34 | it again, then release button) |
||
35 | |||
36 | 1) connect your pc to the LAN port |
||
37 | 2) be sure your link is up and has an address in the |
||
38 | 192.168.1.0/24 address range (and not the 192.168.1.1) |
||
39 | |||
40 | Notes for Toshiba router: |
||
41 | boot_wait is enabled by default on these units. |
||
42 | |||
43 | 1) connect your pc to any of the four LAN ports |
||
44 | 2) be sure your link is up and has an address in the |
||
45 | 192.168.10.1/24 address range (and not the 192.168.10.1) |
||
46 | 3) run this script (unit will only accept .trx images) |
||
47 | 4) Turn unit power on. |
||
48 | |||
49 | EOF |
||
50 | exit 0 |
||
51 | fi |
||
52 | if [ "$2" = "asus" ]; then |
||
53 | echo Confirming IP address setting... |
||
54 | echo -en "get ASUSSPACELINK\x01\x01\xa8\xc0 /dev/null\nquit\n" | tftp 192.168.1.1 |
||
55 | echo Flashing 192.168.1.1 using $1... |
||
56 | echo -en "binary\nput $1 ASUSSPACELINK\nquit\n" | tftp 192.168.1.1 |
||
57 | echo Please wait until leds stops flashing. |
||
58 | elif [ "$2" = "linksys" ]; then |
||
59 | echo Flashing 192.168.1.1 using $1... |
||
60 | echo -en "rexmt 1\ntrace\nbinary\nput $1\nquit\n" | tftp 192.168.1.1 |
||
61 | echo Please wait until power led stops flashing. Do not poweroff! Then you can login via telnet 192.168.1.1. |
||
62 | elif [ "$2" = "toshiba" ]; then |
||
63 | echo Flashing 192.168.10.1 using $1... |
||
64 | echo -en "rexmt 1\ntrace\nbinary\nput $1\nquit\n" | tftp 192.168.10.1 |
||
65 | echo Unit will automatically reboot within 5 minutes. Do not power off. Then you can login via telnet 192.168.10.1. |
||
66 | fi |